Kundeanmeldelser for VEVOR 2 hk båndsliper med konstant hastighet, 2 x 82 tommers båndsliper med 3 slipeskiver, 110 V benksliper, 12 tommers hjul og flat plate, verktøystøtte for knivproduksjon

Franchement pour le prix rien a dire, c'est robuste ,efficace. Ce n'est pas un vrai équipements de professionnels mais pour commencer et évoluer sincèrement ça vaux le coups. Livraison dans les temps et bien protégé dans une caisse en bois.

produit reçu sous une semaine, bon suivi. a voir a l'utilisation mais il semble de tres bonne qualité, livré dans une caisse en bois et bien protégé. le prix est attractif mais il faut compter environ 15€ de frais de douanes non signalé sur le site

This one is a good addition to any shop,knife maker, or blacksmith. Easy to change belts or attachments. It needs a holder for the Allen wrench to change accessories and it also needs a bigger work table. The VFD will read HZ and not RPM no manual to explain the VFD but you get to know it with use. Some of the welds is a little bit questionable but holding for now if they need it later I will welds them then.

This is a really good general little belt grinder. Its small but don't let that fool you, It can grind a knife down, do bevels handle then sharpen it . It may take a little longer but if your in ance out hurry or production you should have gotten a professional one instead. This one is a good all around the shop grinder and belt swap is super easy..Two suggestions to make it better is a stiffer spring or a tension rod on the belt to keep it tighter and some bounce out of the belt. Also needs a bigger table or work on or offer a bigger add on.

Braucht noch etwas Fein Tuning. Die Bandspannung ist etwas zu hoch und es ist nicht alles im Winkel (eher Kosmetik) . Trotzdem perfekt fürs Geld.

Der Bandschleifer ist solide gebaut, funktioniert einwandfrei, die 25mm Bandbreite sind halt limitierten und bei mehr Druck /längerem Schleifen wird die Führungsplatte / Anlage des Bandes recht schnell heiß. Ich hab mir eine Hitzeschutzfolie auf die Anlage geschraubt, damit geht s gut. Für meine (Hobby) Zwecke bisher gut.

Ottimo prodotto

Zum Messerschleifen und ausdünnen ganz ok

This 2 x 72 belt sander is a solid machine for the price. Tolerances are a bit loose so I had to do a little shiming here and there to get things square. I wish it had a secondary tool arm so I could use or build a surfacing attachment, a better table and sharpening jig. The table it comes with is not great. Outside of that its has a good motor and tracks pretty good. It worth the price for the most part.

This is a suprisingly good grinder for the price. It has features more common with larger and more expensive grinders (i.e. do you want a flat platen vs a contact wheel, do you want to run vertically vs horizontally). It comes with a reversible speed controller. Don't know if you've priced those out by themselves at any time, but for this price, I was very pleased to have that included. The build is pretty solid, and the only issue I have is that some of the adjustable features (table angle etc...) are held in place by a single allen bolt. It's not an uncommon feature, even among more expensive grinders (same with my burr king 2x72), but given the lighter build (aluminum not steel), these things would be more secure with a double bolt system (easily remedied with a drill, a tap, and another bolt...). The variable speed is great, and the motor seems to be difficult to bog down. Honestly, the limits of what you can do with this grinder are mostly going to depend on you, the belts you can get, and limits inherent to a 1x30". This sander has worked great so far doing handle contouring, fine work on a guard, and roughing in sharpening at lower speeds.