Kundeanmeldelser for VEVOR hoggesag 14 tommers gjæringskappesag for skjæring av metall tørrkappsag 45° vinkel

Una magnifica sierra tronzadora de metal , disco de corte de muy buena calidad y herramienta potente y sin apenas vibraciones , por sacarle un defecto ,el elemento que bloquea el brazo de la sierra es de dudosa calidad ,el muelle no sirve para nada y en ocasiones no bloquea bien o se queda algo bloqueado .

Hasta el momento todo bien es una máquina robusta y se siente de buena calidad, también el envío fue muy rápido, es la primera vez que compró en la página oficial de vevor y me pareció muy buena atención

Quality/ premium tools come at a cost which Ive always accepted when tools were my way of earning a living. When it comes to handyman work and mancave tinkering, I look for well priced tools with good bones that I can easily mod from a okay tool to a great tool. Pros: This tungsten blade steel cutoff saw is one of those bargains. The base and hinge assy is solid with no noticeable movement. The fence is cast steel and solid held by M10 bolts. The sawblade look reasonable. Ill test it tomorrow. Cons: The drive gear (motor to blade spindle) it quite loud. I suspect that it's a straight cut gear not a bevel cut gear but that to be expected for the price. I accept that. The fence when loosened off slops around like a ____ in a top hat. Having a fence with a tight pivot is high on the list of must haves for me. Particularly because the angle cutting scale is typically very inaccurate. Easy fix if you're reasonably handy. Ive done a basic fix which anyone with basic skills can do. Later Ill push a 14mm mill through the pivot hole and machine up a brass bush to press in but this fix I did for those without a lathe. I had some 12mm OD tubing. I drilled the pivot hole with a 12mm drill bit which is actually 11.9mm and pressed in a piece of tubing 12.5mm long. Then used a dress press to drill a 10mm hole through the tube bush. I placed a 12mm ID washer over the bush then replaced the M10 bolt + M10 washer. Now the pivot action is smooth and snug. For the rear angle locking bolt, put a large M10 washer under the existing bolt so the fence can rotate without getting caught on the punched cutting angle numbers. I also added a cable clip to the power cord to ensure that it doesn't get caught up in the cutting blade as it sits very close to the blade. Set-up. Next, take your time to set the fence to exactly 90deg for a square cut with the two bolts locked down. Now with a sharp scribe score the saw bed against the fence down to the bare steel. Now when you set the fence to a square cut you can do it quickly. Do the same for a 45deg and scribe the base. J generally only do 90s and 45s which I can no set the saw in seconds. I hope this info helps someone. Just to add, powder coating is very slippery so with angle cuts it's almost impossible to stop the fence from moving as you tighten the clamp. Use a flap disc and rough up the underside of the fence. I also roughed up the area under the fence to improve grip.

Quality can be better , The angle is not accurate.

Es una máquina robusta y confiable, potente y muy estable, puedes calibrarla si es necesario ya que tiene un árbol de aluminio sólido unido al mecanismo que te permite accionar el disco. Trae de fábrica un disco de 66 dientes que te permite hacer cortes en muchos materiales, incluyendo acero dulce calibre grueso. Para mejor desempeño le puse un disco de 90 dientes y los cortes mejoraron mucho y me permiten cortar acero en calibres delgados. Es una excelente máquina, la recomiendo mucho

Cheap and cheerful, but be very careful with the blade. I like the fact that the clamp pivots both + and - 45°

Kam beschädigt an und auch die Lager machen laute Geräusche. Keine Reaktion vom Kundenservice. Ganz schlechter Service und ganz miese Kommunikation!

The base of the unit I received was warped from the factory. A part sitting in the clamp can rock back and forth up to 2 degrees with no way to know if the cut will be square. Because it is warped directly under the blade, the free end of the cut has a possibility to bind on the blade as the cut progresses. Additionally, the angle adjustment is inaccurate. The angle adjustment pivot has something like 1/8" of play so you could never make a miter you could trust to be reasonable accurate to build with without measuring the angle by hand somehow. Both of these problems would be easily fixed if the company would accept the defect in the product but I contacted Vevor about the defect and this is their response: "The base has a slight curve: This is due to the base's thickness, but it does not affect the balance of the cutting process. Cutting angle issues: With any machine of this type, accuracy is limited, not precision." Its surprising to see such an obviously problematic defect dismissed as acceptable by the company. They company will not accept a return for the saw and they offered me first a $25 refund then a $75 refund to help cover the cost to repair the base. I guess I'll be designing a new base for this before I can use it. I didn't have high precision expectations given the low cost of this saw but if you want to make reasonably square cuts, I'd look at one of the other options.