Kundeanmeldelser for VEVOR Ikke-svingbar freseskruestikke med låsing, 4 tommers presisjonsbenkklemme, 100 mm bredde, borepressklemme, 4 tommers kjeveåpning, for etterbehandling av fresemaskiner, boremaskiner, presisjonsdeler

Jeg modtog min skruestik den 06-11-2023 og tog den i brug den 22-11-2023. Jeg borede huller i en plade til en lampeholder. Det gik fint, og den holdt emnet urokkeligt fast. Den blev brugt i lodret posision, jeg har endnu ikke prøvet den i vandret posision, men det kommer nok. Se venligst vedhæftede billeder, hvis de er med, jeg er ikke sikker på at de er kopieret MwH. Bent Delfs

I needed a vise that does not lift the moving jaw and not very large. After checking several tests at Youtube i found I could buy locally but from Vevor in EU I had the best price. Fast delivery as well. I stoned all sharp edges and cleaned everything thoroughly, then reoiled with way oil. After reassembly I have used it several times and I am fully satisfied with it's performance. Since some years I also have a Vevor dividing appararus for my milling machine that works fine. I recommend this vise as good value for money

Tolles Produkt, schnelle Lieferung; kann es nur weiter empfehlen; gut verpackt geliefert, einfache Handhabung.

buena compra, usada para una fresadora pequeña que me he comprado, tiene buen agarre y buena presion a la pieza, no observo holgunas en apriete

Erittäin laadukas, toimii niinkuin pitääkin. Toimitus oli erittäin nopea. Tuotetta voi suositella vaikka ammattikäyttöön.

Very pleased with my purchase. These two smaller vices complement a larger one. I was expecting to see the coolant drain, but this rotating model is perhaps too small for that.

It's cheap and cheerful, for the money it's bloody good, I ran a dti over it and it was within 0.01mm on X,Y&Z. edges needed easing as many youtube reviews have said, The base was pretty good I ran a stone over it and although not absolutely perfect I wasn't concerned about anything. The jaws I will probably replace as when the vice arrived they were ground flat on the top, I assume once assembled. once taken apart there is no repeatability. I had to jiggle them about a bit to get them back trammed with the dti. but hey ho it's not a Kurt and not a Kurt price. I can't really comment on the swivel base as I only checked for parallelism. for the deg if I wanted accuracy I would use a sine bar anyway. One thing I did notice was 0 deg started underneath the screw, making 90 deg to the side where there is a mark for setting, no problem for me though. I have the vice on the bed with no base, used my own T nuts and bolts as they were better. For the money it is very good value in my opinion, and would not hesitate in purchasing another should the need arise .

Très bon étau massif et plutôt précis vue le prix .peut être un peut trop gros pour mon usage, mais vue le prix il ne faut pas hésiter

Deze spanvijs doet wat moet , voor de prijs moet je het zeker niet laten, ik heb deze gekozen met draaitafel want die kan er gewoon eraf en misschien later eens gebruikt worden als die echt nodig is het prijs verschil is dan ook miniem vergeleken met deze zonder draaitafel!

I needed a vise a little bigger than the 3.5" one which I have for my RF30 mill/drill (full ballscrew/ cnc conversion)and this is perfect. I especially like the included guide lugs, they make swapping the vise on and off the table a snap with minimal trueing needed. Speaking of which, the swivel feature makes trueing it to the table a snap and does not appear to affect the rigidity. I like it so much and the quality is such that I just ordered one of your 5" dividing heads. Just a note that by purchasing direct from Vevor I saved over $50 over purchasing through Amazon!