Kundeanmeldelser for VEVOR 4-pakning kabelrekkverksstolpe, 36x1x2 tommer horisontal hulls dekkrekkverksstolpe med forhåndsborede hull, kabelrekkverksstolpe i rustfritt stål med horisontal og buet brakett, svart, 4JZLGZXHS914UUOI6001V0

Trés bien pour la fonction et si on l’installe soi même on fait vraiment des économies

Everything was OK.

Overall very good experience using the vevor cable railing system. Would highly reccomend this product to the average handyman. I spent approximately $2600 to complete 50' of railing, including these top rails, the posts, 1/8" wire rope, wire/post protector sleeves, wire tensioners, as well as vevors hydraulic crimping tool. Cons: - the main hiccup in my project was vevor sending me half 42" and half 36" posts despite ordering all 42" posts. After a couple day back-and-forth, they refunded the posts for the full cost and allowed me to keep the posts. - the posts only come with concrete anchor, so I needed to buy some GRK screws from hardware store to secure them to my wooden structure. - be careful as the black metal is very easy to scratch. It is difficult to fasten the top rail to the posts. I had best success putting a couple layers tape around the top of the post to protect it. - the "self tapping" crews that came with the posts to fasten to the top rail do not work at all, even when everything is pre drilled. Do not waste your time, and get some hex-head self tapping screws from a hardware store. Pros: - everything I received is very high quality and robust. Very easy to install. The entire project took my approximately 12-15 hrs. to complete - the top rail can be cut (I used an angle grinder with a higher quality metal disk) - the cable system does not sacrifice your view, and looks very modern and clean

Worked well. Order came through quickly. No complaints yet. The price was right, as usual. Thanks Vevor !

The posts seem well built and the powder coating seems to hold up pretty well. I would have preferred the 2" x 2" posts and was a little apprehensive about the 1" x 2" posts but they work just fine as deck posts. And I can't find a better price than these anywhere. I am a happy customer.

Pricing A++++++ Quality was better than anticipated with great price. Shipping materials were sufficient and product arrived safe. Easy install. Product comes with concrete anchor bolts needed bolts/lags for deck install Already Recommended to other customers

Recently built a deck, installed cable rail around the perimeter. Can't beat the cost of these, they're literally half the cost (or less) than pretty much everything else on the market. Posts are solid, definitely good stainless (non-magnetic) so they should last forever. The only complaint is the top where the railing gets attached. You can not get it tight enough to support the end of a run. Once you start tightening the cables, you can see it visibly start to fail. I also used the posts for an indoor railing around my stairs to the basement. Love the look, just wish the top was a little stronger. You can see in the photo how it's not straight. This is with minimal tension with 1/8 cable. I used 5/32 outdoors and it was much worse, ultimately had to install extra bracing to keep it from failing.

Quality, fit, finish, and value make many of vevor's products great. These deck rail parts are no exception.

This product is great and well constructed. I think they should make a video of how to install it because the installation instructions are not to clear. Step 1: Install your posts about 4 to 5 feet apart, not more and level them. ( I went 4 FT apart) Step 2, install your hand rail. You should use a drill press because you need to spray oil on your drill bit while applying good pressure. The handrail is very hard to drill through. Cut the hand rails with a chop saw using a metal blade, you will also need a grinder or a metal hand file for the edges which will be sharp. Install the hand rail temporarily and mark your holes with a sharpy, I used cable ties to secure the railing temporarily. Step3: Install the cable and don't forget the protector sleeves. The protector sleeves are not required but do a better finishing job, however, they don't really fit in the corner post. You will need a hydraulic crimping tool to crimp the sleeves at both end, double crimp them if you can. Run your cable through the first post and add the protector sleeves as you go, at the end, crimp the end sleeve and run it in the post hole. Go to the other end, pull on the cable to tighten it and mark the cable at the point before it enters the hole in your post and that will be your length required.

These railing posts are solid. Easy to install and totally secure and straight. Appears to be powder coated but I'm not sure, either way the paint feels like it'll hold up well. I will be buying a lot more of these for my entire backyard project.