Kundeanmeldelser for VEVOR 47 tommers flisekutter enkeltskinne doble braketter manuell flisekutter 3/5 tommers hette med presis laser manuell flisekutterverktøy for presisjonsskjæring egnet for porselen og keramiske gulvfliser

Envio fora de prazo e sem rastreio. A máquina de corte de cerâmica manual chegou com defeito nas borrachas dos apoios laterais, enviei fotos da situação e estou a aguardar que enviem substituição da peça com defeito.

Atraso na entrega não cumpriu com o prometido no ato da compra. Embalagem parcialmente aberta, tampa da caixa de bateria quebrada, base e haste flexíveis nao oferece segurança

For the price the quality is fine, but it does have some flaws that keep me from using it on a daily basis. 1. The piece that has to snap the tile after scoring can not be held up, so it’s always hanging in the way when cutting. That is quite annoying if you’re trying to cut precisely. 2. The laser attached is basically useless, since it doesn’t have enough options to calibrate it to be precise/usable. It can only be rotated, not moved from left to right. 3. Also the guide or “tile stop” is totally out of square, so basically unusable. 4. The ad claimed it has a carbide roller blade, but it doesn’t have it. So it dulls very quickly, had to buy a real carbide blade separately. A few minor tweaks could have made it way better, but they chose not to which is disappointing.

laser never worked. have not used yet to cut but i am sure will work just fine

Mais je n’est pas réussi à couper les carreaux sur la longueur ils cassent toujours à un endroit malgres la coupe faite bien droite. Dommage. Peut être mes carreaux qui ne convienne pas.

todo ok

I bought this to cut large format tiles, 24 x 48. I have several smaller cutters. The trend to larger tile sizes forced me to get a new bigger one. The packaging looks good on the outside. However when I set it up and started using it I quickly realized it was going to be a challenge to get the job done correctly. One of the biggest gripes I have is they didn't calibrate the tool. There maybe a laser mounted on the head but as is out of the box it's useless. You will need to adjust it. Then I put a tile in and scored it, pressing the snap bar separated the two halves. pull it out from the bed and how off square could it be? Try 1/8" per foot. That is ridiculous. The rails seem too thin for the length that they are. The car slides nicely. There are these wings on the sides to support tile overhang. They are flimsy are get in the way if you're not using them. The unit is put together with nylock bolts and screws. Put aside 3 hours to setup and calibrate. It's not ready to use as is out of the box. Would look elsewhere for a more robust accurate tool.

Bardzo słaba . Wygina się i nie docina płytki. Zakres pracy noża jest zbyt wysoki. Nóż tnący nie dochodzi do płytki z wystarczającym dociskiem. Cała konstrukcja wygina się przy próbie docisku płytki przy jej podziale po wycięciu linii. Lepiej dołożyć 200-300 złotych i kupić lepszy sprzęt. VEVOR spróbuje sprzedać .

Nach 6 Fliesen schneiden, kann ich Diamantscheibe wegschmeißen sehr billig gemacht

Belle longueur certes… aucun réglages corrects… équerrage pourri, laser pas droit bref assemblée en chine. Et les deux barres de guidage qui se courbent à chaque marquage de carreaux. Bref je suis très déçu. En plus je l’ai payé plus de 100€. J’aimerais un avoir ou être remboursé car le produit ne correspond pas du tout à mes attentes