Kundeanmeldelser for VEVOR 600 mm flisekutter Enkel skinne Doble braketter Manuell flisekutter 1,5 cm hette med presis laser Manuell flisekutter Verktøy for presisjonsskjæring

Zawiodłem się, liczyłem na lepsza jakości, przecinarka się wygina, na dodatek na środku źle docina, a czasami przy gresie 7 mm raczka opiera się na prowadnicy i nie idzie noża docisnąć bo palce przeszkadzają, ustawiałem na różnych podłożach, efekt ten sam szczególnie prze mniejszych rozmiarach płytek typu 30cm 40cm

Came partially assembled one of the side support legs wasn't installed and in order to install it needs to be disassembled , bearings not one was spinning freely because the washers were installed at the front of the spacers onto the bearings and that was stopping them from spinning so again need to be switched around so basically complete disassemble to fix this issues then the laser is not 4 screw adjustable only two and is impossible to align it if the back aligned to the cutting wheel then the front at least 1/8" off if the front aligned then 1.5 " at the back is off I tried for an hour and not possible to align it , the breaker shoe doesn't have a magnet to hold it up when you score so it's a bit annoying, I am disappointed!

Envio fora de prazo e sem rastreio. A máquina de corte de cerâmica manual chegou com defeito nas borrachas dos apoios laterais, enviei fotos da situação e estou a aguardar que enviem substituição da peça com defeito.

Mais je n’est pas réussi à couper les carreaux sur la longueur ils cassent toujours à un endroit malgres la coupe faite bien droite. Dommage. Peut être mes carreaux qui ne convienne pas.

todo ok

Ich habe das Produkt gekauft um Fliesen im Format 20x120 zu schneiden. Das Gerät ist recht simpel in der Nutzung. Leider ist die Qualität nicht sonderlich gut. Der Anschlag ist etwas schräg montiert, sodass die Fliese nicht rechtwinklig angelegt werden kann. Der Laser lässt sich ebenfalls nur bedingt einstellen, sodass er entweder am Endanschlag oder am Anfang die Schnittstelle markiert. Zudem ist die Führungsschiene etwas schwach bemessen, sodass sich beim Anreißen in der Mitte der Fliese die Führung hochdrückt und der Riss nicht sauber ist. Für den angebotenen Preis im Bereich Hobby Gerät ist es okay. Der Support zu den angegebenen Problemen war leider sehr schlecht. Mir wurde 3x die Anleitung des Produktes geschickt, statt auf die Probleme einzugehen

La taglia mattonelle e perfetta per me ha solo un difetto quando tagli le mattonelle già da 2/3 cm sulla lunghezza di 120 non si riesce a tagliare si spezza sempre e in più si inarca molto al centro andrebbe studiato un rinforzo al centro

I bought the 47 inch tile cutter about 2 months ago and have done one project with it. I found the laser light useful particularly as the built in square on the tool was not square. The roller cutter was smooth and cut cleanly. There was flex in the base so one had to ensure it was on a solid table. I would not recommend this tile cutter for extended use as it required more measuring because of the out of square guide.

This was of some use for a while but it doesn’t cut accurately and the rails are weak and flex, look, you get what you pay for but I wouldn’t buy another one and ended up spending much more money on a descent tile cutter

I bought this to cut large format tiles, 24 x 48. I have several smaller cutters. The trend to larger tile sizes forced me to get a new bigger one. The packaging looks good on the outside. However when I set it up and started using it I quickly realized it was going to be a challenge to get the job done correctly. One of the biggest gripes I have is they didn't calibrate the tool. There maybe a laser mounted on the head but as is out of the box it's useless. You will need to adjust it. Then I put a tile in and scored it, pressing the snap bar separated the two halves. pull it out from the bed and how off square could it be? Try 1/8" per foot. That is ridiculous. The rails seem too thin for the length that they are. The car slides nicely. There are these wings on the sides to support tile overhang. They are flimsy are get in the way if you're not using them. The unit is put together with nylock bolts and screws. Put aside 3 hours to setup and calibrate. It's not ready to use as is out of the box. Would look elsewhere for a more robust accurate tool.