Kundeanmeldelser for VEVOR båndsliper, 72 x 2-tommers båndpoleringsmaskin med variabel hastighet og VFD, 1500W 2HK poleringsslipemaskin med 3 slipeformer og 3 stk. slipebånd for metallbearbeiding og knivproduksjon

I have had this machine a week and so far I have been unable to use it because the thing is total garbage. The belt wont track no matter what I do to adjust anything and everything. the square tube that the other piece goes into looks like discarded remnants and the accesory just flops around in the hole. Funny, I dont see the same issue with the free machines being sent to youtubers. the tracking wheel has a ton of problems. The adjustment wheel is not sitting straight. I have done everything to try and fix that issue, and it is still sitting at a tilted cant. The needle bearings riding on cheap washers are already digging into the washers because needle bearings should not be riding on simple washers. I had to machine some stainless washer/bushings to address that. The plate that holds the adjustment wheel doesn't fully support the washers/bushings. the sleeve pin looks like it was rough ground by hand and the base of that pin needed trued up int he lathe, and its free floating, not sure why but that pin should be pressed into the plate and welded secure so the adjustment wheel rides on that pin instead of relying on clamping pressure to force the adjustment wheel straight. I tried adjusting the motor, and no luck there either, the motor is sitting all way at the end of its adjustment travel. THAT ALONE SHOULD BE A RED FLAG. I have gone over everything and the belt will not track properly and sticks off the front rollers. This means I cant grind on that, if I make the adjustment so the belt is centered on the front wheels, the belt is then overhanging on the adjustment wheel and thats still a problem because one, that's not how that should be and 2, that overhand will cause the belts on it to come undone and destroy themselves. And I have invested in 3 very expensive belts and Im not going to let those belts be ruined because vevor is scamming the public on trash machines. The base has an elongated curve in it so it doesn't sit flat on the table, and it rocks back and forth. I had to put a heavy bar mat under it to take up that bend so it would not rock back and forth. WHERE IS THE ON AND OFF SWITCH? Previous belt grinders had them. The VFD has no protection from grinding dust entering it and gosh, I wonder what issues will result from that. I had to buy an expensive 30 amp on and off switch so I could turn this machine on and off. The large wheel that came with this has deep nicks in the wheel. Since when is it ok to send stuff like this to customers? Vevor needs to be held accountable at a much higher level than just their corporate complaint dept. This nonsense is dishonest and needs to stop. I made a full review video posted on Opies Home Shop on YT for all to see and its not a good review oh vevor! https://www.youtube.com/watch?v=hh30YucXXJE

Grinder itself is an awesome little piece,but resign yourself to the fact you'll just have to buy another unit if in fact you need parts or support. 3 separate times I've submitted warranty requests or support,even offering to BUY parts to replace things and they basically told me they can't help. Then offer what amounts to a 20% off coupon to have to go buy an entire unit. I guess for the price you can't go wrong, and the grinder itself is an awesome unit to enter into knife making especially.

Jamais reçu la commande, plus de 1 mois de perdu!! Une catastrophe leur service de livraison, personne ne vous contacte rien.

The grinder looks good, unfortunately the drive wheel on the motor is very unbalanced and the whole grinder vibrates a lot. I tried printing a new one on a 3D printer and the grinder runs beautifully without vibrations. I haven't tried the large contact wheel yet so hopefully it will be good, it is definitely not balanced. Bruska vypadá dobře, bohužel hnací kolo na motoru je hodně nevyvážené a celá bruska značně vibruje. Zkusil jsem si vytisknout nové na 3D tiskárně a bruska jede krásně bez vibrací. Ještě jsem nezkoušel velké kontaktní kolo tak snad bude dobré, vyvažované určitě není.

I have been using this for a bit now and there are a few things that would help to make this a 5 star machine. First the table is so small that it’s pretty much useless. I made one that’s 10” by 4” and it works perfectly. Second the mount that holds the table holds it about an inch too high making it hard to use knife grinding jigs. If you make one an inch lower it works much better. Third the mounting holes and pins for the accessories are very smooth and even tightened down hard they tend to move and change angles. Roughing them up with sand paper helps. Overall the speed and torque are perfect. It’s quiet and easy to use. Just could be better.

Des produits avec un rapport qualité/prix très correct surtout pour les artisans en transition entre débutants et professionnels. Cependant, en cas de problèmes le SAV a pris un mois et demi pour m'envoyer un modulateur de rechange. Je pense continuer de me fournir chez Vevor mais je limiterais mes achats au matériel dépourvu d'électronique.

Bandschuurmachine voor onze zoon van 12 gekocht omdat deze helemaal verkocht is aan het smeden van messen. Op zichzelf een mooie machine echter één ding de machine kan niet aangesloten worden op netstroom in huis omdat de aardschakelaar eruit vliegt door de toerenregelaar. Navraag gedaan bij een elektromonteur en die bevestigde inderdaad dat het niet mogelijk is om een bandschuurmachine met een toerenregelaar aan te sluiten op het stroomnet behalve als je er een aparte groep voor laat installeren die dan alleen voor de machine is aangelegd. Het zou wenselijk zijn als er in de omschrijving stond vermeldt dat dit product niet geschikt is voor huishoudelijke netstroom.

Very poor quality, the sander lasted 3 months before it started giving me an ER 6 code and would not operate. I couldn't find any repair information for the sander. Vevor did refund 60.00 of the original price.

Das gerät lässt sich programmieren aber keine Anleitung dabei. Dafür wird behauptet das würde nicht stimmen, es gäbe keine Programmierung!

Bonjour Le site ne propose pas de bande abrasive ni la REF ni les dimensions pour en avoir d'avance CLD PIOT P