Kundeanmeldelser for VEVOR 10 kg (22 lbs) smedambolt 55HRC stålsmedverktøy 35,3 x 11,3 x 16 cm ambolt med en arbeidsflate på 355 x 110 mm Ideell for metallbearbeiding, nagling, flating, smiing og forming av metall
Kunde anmeldelser
Hvordan kundeanmeldelser og -vurderinger fungerer
Kundeanmeldelser, inkludert produktstjernevurderinger, hjelper kunder med å lære mer om produktet og avgjøre om det er det rette produktet for dem.
Den samlede vurderingen vår er ikke et enkelt gjennomsnitt. Vi prioriterer autentiske og troverdige anmeldelser og filtrerer ut duplikater eller ugyldig innhold før vi beregner den endelige poengsummen. Dette bidrar til å sikre at vurderingen virkelig gjenspeiler reelle kundeopplevelser.
Anmeld dette produktet
Del tankene dine med andre kunder
Skriv en anmeldelse
610 Anmeldelser
Anmeldelser for Gjeldende Produkt
Verifisert kjøp
Bilder og video kun
Oversett alle anmeldelser til Norsk (Berkmel)
Rob Veteran
This anvil does what an anvil needs to do in that it is a heavy block of metal to work hot steel on, and it's very reasonably priced. It has some shortcomings, however: 1) the horn is way too fat to be truly useful for fine blacksmithing; 2) the open belly sacrifices mass that would make the anvil much more solid if that void were filled; 3) the casting is poor, leaving the body with holes and porosity that gets covered with plastic body filler; and 4) the Pritchel (or punch) hole (the round hole) is in a completely useless position, and it is way too big. Instead of drilling it one-inch in diameter in the horn, drill it 1/2" to 9/16" in the heel, between the Hardy (square) hole and the end of the heel.
1 personer syntes dette var nyttig
Oversett anmeldelse til Norsk (Berkmel)
anvil little horn
over all it is good, my only complaint is the the top has milling lines it is not a smooth finish. Other than that A+
0 personer syntes dette var nyttig
Oversett anmeldelse til Norsk (Berkmel)
Kevin Levesque 66 lb London anvil
The weight and general appearance of the Anvil was very nice.
Upon dressing the edges I noted some deep chips from the casting that took a bit to clean up. The Hardy hole had excessive metal I had to carefully sand out. This excessive metal was a bit above expected clean up.
I’ve yet to run my hammers and steel on it but it seems solid and my bounce test was very exceptable @approximately 80%
Time will tell how well it holds up but so far I am not disappointed in the general appearance
0 personer syntes dette var nyttig
Oversett anmeldelse til Norsk (Berkmel)
Markus Anvil
Good for the price, needs a little finishing but nothing serious
0 personer syntes dette var nyttig
Oversett anmeldelse til Norsk (Berkmel)
Orange Usable
Very good starting anvil, if you take care of it it will last
0 personer syntes dette var nyttig
Oversett anmeldelse til Norsk (Berkmel)
Curt Mr
The hardy was very rough I had to file it down and grind off my hardy tools
0 personer syntes dette var nyttig
Oversett anmeldelse til Norsk (Berkmel)
Glong1955 Anvil
Great small anvil , it needs some refining before use.
Hardy hoke is a little big for a small anvil
Overall very good for the money
1 personer syntes dette var nyttig
Oversett anmeldelse til Norsk (Berkmel)
Mathprio 👍
L'enclume est très bien, mais elle n'a pas assez de rebond a mon goût.
0 personer syntes dette var nyttig
Oversett anmeldelse til Norsk (Berkmel)
Dustin Williams Good stuff
No complaints work fine
0 personer syntes dette var nyttig
Oversett anmeldelse til Norsk (Berkmel)
OD Barner Mr
My only complaint is that the horn is a bit rough. Some sanding will clean it up. But it could be smoother.
0 personer syntes dette var nyttig
Oversett anmeldelse til Norsk (Berkmel)
