Kundeanmeldelser for VEVOR Elektrisk Honningekstraktor Tangensiell Ekstraktor Birøkterhonning 2/4 Ramme

Over all satisfied with the purchase. Easy to assemble and easy to move from one place to another, not heavy at all. Tried to extract 4 medium frames radially, but wasn't happy about the outcome. Too much of honey left in the frame. Then I tried extracting frames tangentially, putting frames parallel to the walls. Using this method you need to extract one side and then reverse the sides and extract again. So it is a bit time consuming. The other problem is the drain cap is about inch above the bottom, so get all the honey out you need to tilt the extractor which is a pain. Overall happy with the performance.

Prima honing slinger apparaat, doet wat het moet doen en dat voor een lage prijs. ik heb de honing slinger niet vast ergens op gemonteerd tijdens het gebruik en daarom onder de poten trilling rubbers gemonteerd. ik adviseer om alle reeds gemonteerde schroefjes en boutjes te controleren of ze goed vast zitten ,anders trillen ze waarschijnlijk los. prima product voor de kleine imker.

Works great. Wobbles if you don't brace the legs. A simple 2x4 T plate reduced the wobble a lot. Other than the drain being to high up it is a good unit overall. Would buy again!

You can’t beat the price. It works good. Came dented but popped right out. Missing a screw for the safety switch. Just had to buy my own screw for it. But it works great and glad I purchased it

Franchement à ce prix là, faut pas se priver... les pieds sont toutefois fragiles (peut être qu'avec un quatrième pied il eut été plus stable) et je n'ai pas trouvé la solution idéale pour stabiliser correctement l'engin en vitesse de croisière. La partie moteur peut se désolidariser de la cuve pour le nettoyage, ça c'est top, dommage que le mode d'emploi n'en parle pas pour montrer comment on procède.

I purchased this Vevor 4/8 electric extractor as my first extractor, and was overall very pleased. Assembly is straightforward. The motor is quite quiet as is the full process when your spinning with some balance in the frame holder. If running out of balance try to minimize by inserting another frame(s) to reduce the mismatch. In these cases bolting down the legs would help. We had fun extracting 66.5 lbs from 14 frames, some deep and some medium or shallow. Ultimately placing either size in tangentially provided us the best results. Trying to spin the smaller frames radially didn’t work effectively for us. Clean up was relatively easy. The single piece frame holder has to be removed for a thorough cleaning and this can only be done by removing four nuts to remove the cover/motor assembly. That feature makes an economic design but is why I rated a four and not a five on features. After leaning the extractor on its side to pour all remaining honey through the honey valve we still spooned out another 1.5 lbs from inside before deciding to stop and clean. Overall, I recommend it.

je recommande ce produit. arrivé très bien emballé et dans les délais. utilisé pour extraction de miel, petit bémol : cet extracteur n accepte pas pas les cadres type Hoffman pour quelques minimètres, pas de soucis avec les cadres droits. pas de possibilité d inverser le centre de rotation. la vitesse de rotation pas assez rapide à mon sens mais j ai compensé en augmentant la durée de rotation. qualité prix

Using it for my second season. So far so good. I have about 100 frames extracted at this point. Legs are a little weak but functional. Not a commercial unit but good enough for now.

Good value for money, the stands are a bit week and could be a bit taller to accommodate a bigger bucket.

Sehr gutes Preis-/ Leistungsverhältnis. Qualität gut, Kanten teilweise etwas scharf. Kleiner Minuspunkt ist der relativ hohe Auslass. Geht mit Kippen auch, aber halt mühsamer. Trotzdem absolut zu empfehlen