Kundeanmeldelser for VEVOR papirkutter 12" A4 giljotiner papirtrimmer 400 ark kapasitet metallbase

Trop complique et pas conforme a la description Il manque une partie Trs decuv

I bought this cutter less than 10 months ago. I bought it to cut down greeting cards which are on a card stock. I was surprised that it had a hard time cutting through 10 sheets since it is advertised that it can cut through 400 regular paper sheets at once. I can only cut 6-8 sheets at once only. Anything more it has a hard time getting through. 1) it has now started to cut all my cards crooked 2)the clamp has now started grinding itself inside and leaves shards of metal 3) the clamp doesn't clamp the paper so the paper shifts when the blade comes down to make the cut, resulting in an indent in the final paper 4)blade is very dull only after only using it a handful of times Would not buy and put the money towards something better.

First the safety pin is not working, to short. Next when cutting the blade pulling the paper so it is not align anymore and the top paper is folding and punch, the bottom paper is not cut all the way thrue. So imo it's not worth the money.

The quality is bad. it does not cut at all on the edges ... inspite of bringing down the blade multiple times... Pls do not buy

Bought it for my wife and it doesn’t make straight cuts, the red striking plate sticks up past the deck so you have to lift whatever you cut over it, the plastic alignment arm doesn’t line up with the lines on the deck and every time you cut more than one sheet the blade forces all of the sheets to move closer to the other crooked arm that the plastic alignment arm is attached too, will be figuring out how to return this item

Não gostei nada do produto, pois não atende as minhas necessidades. A base aonde serve de trabalho para o papel não é como a da foto é um ferro com íman que não trás nenhuma estabilidade. A linha de guia de corte mal se vê. Produto extremamente caro para o que ele oferece.

Within 2x use the blade was blunt, the black plastic calibration bar wiggles 5mm in all directions so cutting is also very vague.

I am very disappointed in this product! It has been delivered not as shown. It does not have an adjustable, locking paper bar as shown in the picture. Instead, it has a plastic angle with round magnets on one side to attached to the base of the cutter. This angle will easily move allowing paper to be cut at different unintended lengths

The product I received does not match what was advertised. Several components are inferior—for example, instead of a fixed bar to stabilise the paper, it uses a magnetised bar that constantly shifts position. The biggest issue, however, is that it simply DOES NOT CUT PROPERLY. On the rare occasions it does cut, the results are inconsistent and it often fails to cut through the entire stack of paper. What makes this even more frustrating is that the product arrived with a sticker stating it had been tested at the factory. Given that it does not function correctly out of the box, that claim is difficult to believe. A product like this should arrive ready to use and perform its basic function without requiring manual adjustments. Instead, I had to hunt down a vendor video to find adjustment instructions, as no assembly instructions or instruction on how to adjust it was included in the box. Even after following those adjustments, the cutting performance remained poor and inconsistent. Save yourself the frustration and don't waste your time on this product. I will be seeking a refund.

Product *works* out of the box, instructions were simple to follow, didnt actually need them to use. Safety mechanism failed within days, but that does not stop the tool from working. still functions as a cutter. Issues: 1. The fence that comes pre-installed on the base of the machine is not square to the cutting blade or the printed grid on the tool so cuts are never truly square, and this cant be adjusted as the fence sits in pre cut slots and the bolts are only there to lock it down. 2. The cutting stick that sits under the blade sits proud of the level of the base. so when the paper is sitting flat on the base of the machine, the edge being cut is slightly raised up. so once the cut has been made, if cutting "blocks" of paper, the cut is not vertically square as the paper has been skewed up. There are adjustment bolts that screw in underneath the rubber, but even backed all the way out/removed, it still sits proud. Overall the product is functional. If you are a hobbyist and don't need millimeter perfect angles/cuts, its perfectly adequate. But thats about as far it goes. Adequate.