Kundeanmeldelser for VEVOR papirkutter 12" A4 giljotiner papirtrimmer 400 ark kapasitet metallbase

Creases the paper with each cut, came with an oily residue on all the plastic and makes it very difficult to get precise cuts. It also doesn’t handle more than a few sheets without issue.

Taglia male, storto, dalla prima alla ultima pagina del blocco di carta ci sono più di 2mm di differenza. Quindi non serve a niente avere un taglia carta a blocco se dopo di aver tagliato le misure del blocco variano. Ho contattato al servizio tecnico e la risposta è stata di mettere la carta bene al suo posto e tirare giù della manovella taglia carta 😡 Comprate altro. Questa non vale affatto la pena. Soldi buttati via e un servizio postvendita che lascia tanto da desiderare.

Finalement ne coupe même pas de la cartonette de 2mm. Même molette serrée à fond lla papier ou la cartonette bougent. Lame de mauvaise qualité. La règle de gauche ne sert pas de butée puisqu’elle est voilée et ne touche pas le socle. Je regrette cet achat.

Try to cut and broke

I had two issues with cutter. One is that the cutting blade has a beveled edge on one side that gives a slanted cut . So if you are cutting book board as I was one side of the cut board is not perpendicular to the cutting edge. My second issue was with the fence alignment. Perhaps this may only have been a problem with my cutter but because the fence was off alignment my cuts were not square. The fence is removable but can’t be aligned to square the cuts. I found it unsatisfactory and asked to return it. I sent VEVOR photos to verify my concerns and after more than a week of email exchanges they granted a full refund. I received a full refund in 2 days. I have purchased their products in the past and have been satisfied with my purchases. Hopefully this is a one off situation.

Sballata e messa su un piano NON SPIANA, al massimo dello spessore fa troppa forza e il manico si piega, quando la lama arriva in fondo le viti che la sostengono vanno a rovinare la metà dei fogli tagliati. DA NON ACQUISTARE LA METTERO' IN VENDITA giusto per recuperarci qualcosa. Peccato perchè da Vevor in passato avevo acquistato altro ed è andato tutto bene. L'unico lato positivo: RICEVUTO in soli 10 giorni

Viene desalineada y no se parece a otras que puedes ver en internet para alinearla en condiciones. Además, varios tornillos se le han caido al momento y no puedo ponerselos porque me da miedo intentar desmontarla.

Le produit paraît bien mais il n'y a aucune explication sur les réglages, l'affûtage de la lame. Incapable de couper 3 feuilles proprement. Je ne parle même pas de massicoter 400 feuilles comme indiqué dans la description. Bref dans l'état actuel, je déconseille et je regrette fortement mon achat.

I bought this thinking it would be good for use in our school. Not the case. I unpacked it, no instructions on set up or usage in the box. Went to you tube and not much there. Also did the QR code on the cutter, no luck with that. Tried calling the company, could only use chat, not a live person. Had to send video, I express many times to talk to someone, couldn't do that. I have tried adjusting the screws on the bottom when customer support send me the instruction, but it didn't work. I then requested to send it back. As of this date, I have got NO instructions on sending it back. This cutter is for books or lots of paper, it is not for a school whom cuts 10-30 sheets of paper at a time.

I purchased this solely to cut chipboard, so this review is not geared toward any cutting paper. I was disappointed to see that the handle does bend relatively easily, the adjustable ruler guide feels like a cheap plastic that also bends easily so it is not as accurate as it can be if you need precision, and the clamp handle feels like threads are stripping inside when the clamp is tightened down. Bringing further attention to the clamp, the bottom layer of chip board slides into the frame while cutting, creating a noticeable "bunching" of bent material, and there are different sized cuts through a small stack of chipboard. I was hoping that this would be more convenient than using a box cutter and steel edge, but the lack of accuracy on this cutter has ruined quite a bit of material for me. I probably would have been better off just sticking to my slower, but accurate, method of cutting chipboard.