Kundeanmeldelser for VEVOR papirkutter 12" A4 giljotiner papirtrimmer 400 ark kapasitet metallbase

Product was niet geschikt voor mij maar een super snelle oplossing voorgestelt en afgewerkt

Product *works* out of the box, instructions were simple to follow, didnt actually need them to use. Safety mechanism failed within days, but that does not stop the tool from working. still functions as a cutter. Issues: 1. The fence that comes pre-installed on the base of the machine is not square to the cutting blade or the printed grid on the tool so cuts are never truly square, and this cant be adjusted as the fence sits in pre cut slots and the bolts are only there to lock it down. 2. The cutting stick that sits under the blade sits proud of the level of the base. so when the paper is sitting flat on the base of the machine, the edge being cut is slightly raised up. so once the cut has been made, if cutting "blocks" of paper, the cut is not vertically square as the paper has been skewed up. There are adjustment bolts that screw in underneath the rubber, but even backed all the way out/removed, it still sits proud. Overall the product is functional. If you are a hobbyist and don't need millimeter perfect angles/cuts, its perfectly adequate. But thats about as far it goes. Adequate.

Lieferung ist heute angekommen, pünktlich. Schachtel weist keine Beschädigungen auf. Beim Aufstellen fällt auf, dass die Schneidemaschine nicht gerade steht und wackelt. Jetzt fehlt doch bei der hinteren Ecke der Fuss, die Ecke ist verbogen und es sieht nach einem Sturzschaden aus. In der Schachtel befinden sich keinerlei Bruchteile des Fusses. Der schützende Sagex war vorhanden. Es sieht so aus, als ob beim Verpacken in China das Teil auf den Tisch geknallt ist, den Fuss verlohren hat und trotzdem eingepackt und verschifft wurde. Da staunt der Laie und der Fachmann wundert sich...

Dear Sir or Madam, I am writing to make a complaint about a paper cutter blade I recently purchased from your company. In general, the blade cuts well through about 90% of the sheet. However, in the upper corner—near the handle that is pressed to cut—the blade consistently fails to cut the last part of the paper. About 10 cm of the last two sheets are left uncut every time. Because of this, I have to finish the cut using scissors or a smaller cutter. This defect is causing constant interruptions in my work and is seriously affecting my productivity. I bought this product to speed up and improve my work, but due to this fault, it is not performing as expected. I feel disadvantaged by this issue and would appreciate a solution, such as a replacement, repair, or refund, according to your warranty or customer service policy. Thank you for your attention. I look forward to your response.

Très lourd donc on suppose du matériel de bonne qualité, mais pas de notice de montage, je n’ai donc pas su comment monter la protection bleue, et l’ai jetée à la poubelle car impossible de comprendre comment l’attacher au reste. Ensuite, la coupe n’était pas bonne au départ, il a fallu que je l’utilise quelquefois pour que la lame s’affûte un peu et coupe mieux. Enfin, à chaque coupe, le levier frotte contre une autre partie et la peinture du levier s’écaille, ce qui laisse des résidus noirs de peinture sur le plan de travail à chaque utilisation. La cale en plastique censée bloquer le papier en place ne colle pas complètement à la partie métallique, il y a un espace, ce qui fait que les feuilles en dessous de la pile passent en dessous de la cale. Si l’on ne vérifie pas avant de couper, on se retrouve à avoir des feuilles qui ne sont pas coupées à la même taille que celles du dessus.

I’m not completely satisfied with this knife. The cutting is not as precise as it should be, and one part of the blade doesn’t cut all the way through, which I had to adjust myself. Paper can sometimes slip under the guard (or guide), which affects the accuracy of the cut. The knife is quite solid and feels sturdy at first, giving the impression of a high-quality tool. However, for the type of work it’s intended for—where every millimeter matters—it really should be much more precise.

Virker som den skal

No se si le pillaremos el punto de cortar con la medida exacta, (pues el tope trasero no es muy fiable) ni a cortar tantas hojas como dice, pues aunque sean cincuenta hojas de papel de 80 gramos y apretando bien el pisón hay variación de arriba a bajo.

Product would be great with a few improvements. The back guide needs to be longer going to the opposite side with a clamp or similar screw down guide like opposite side. When you tighten the clamp holding a larger stack of paper in place to cut, the action of the blade pushes the back guide and you get an uneven cut. If you tighten the clamp extra tight that gives you a wrinkle in the stack. I bought some heavy duty magnets to compensate but it is inconvenient when trying to make minute adjustments. The grid doesnt allow for the 1/8" difference between the clamp and the actual blade cut so you need to adjust for this in your measurement. It is best to draw out a cut line and lower the blade somewhat to see if it matches up.