Kundeanmeldelser for VEVOR Manuell honningekstraktor Tangensiell ekstraktor Rustfritt stål 3-rammers honningekstraktor 45 mm honningventil Diagonal ekstraktor 48 x 16 / 23 cm Rammestørrelse Gjennomsiktig lokk Birøkt Birøktertilbehør

I haven't had a chance to use it yet, but I did put it together which was a snap, I beefed up the legs with flat bar, just bolted them to the existing legs and made a base with 3/4" plywood to bolt the unit to. This will stabilize the extractor when spinning the frames, some may be medium and some may be small so the balance may be off a bit when spinning a combination of different frame sizes. I also made up 2 silicon gaskets cut from a silicon pie plate from the dollar store to sandwich between the inner and outer sides of the honey drain spout. these little improvements cost nothing really and I will have no surprises when I start harvesting. It's a nice unit and since I'm retired I have plenty of time to spin 3 frames at a time as apposed to 4 with my old extractor which was too big and so hard to clean.

I only have two hives so this suffice. It's a little narrow to put in the frames, but no big problem. I bolted it to the floor which made it much more stable than stand-alone. The only thing that could be better: Add two spare steel balls !! One way or the other, you will loose at least one. The cost next to nothing if added as spares, but relative expensive if you buy them anywhere later.

Extractor works fine but legs are a little flimsy. Unless bolted down the exterior moves around a lot.

Works well for a beginner, used twice easy to clean bit wobbley but made a wooden T bar so I can hold ut with my foot. Does not fit half sveas very well .....they go but toward end of spinning the fall diagonally, have solved this by squeezing the bottom bar in a bit to keep them more stable. Be warned this does rust easy. Inside has nit rusted but the outside has rusted . Been cleaned with cold water and left out on a warm sunny to day then put in storage both times so can see no other reason that quality....but you get what you pay for. If money isnt restricted, go for a different brand.

PRO: -The Honey Extractor is very easy to install - it looks really nice. - the materials are qualitative. CONS: After first use a welding spot has come off.

Vorige week de slinger ontvangen en in elkaar gezet. Kwaliteit voor het geld is gewoon goed, en is makkelijk te monteren. Waar je wel even rekening mee moet houden is dat de houder/beugel voor de raampjes nét te breed is voor spaarkast honingkamer raampjes waardoor deze er niet netjes in blijven en opzij kunnen vallen. Ik heb bovenin de beugel een tie-rip 'lusje' gemaakt waar ik het bovenste oor van het raampje doorheen steek, en dan zit het stevig en werkt het helemaal prima. Ik heb de handmatige variant waar drie raampjes in kunnen.

E in regula aparatul, in schimb daca vrei sa o returnezi pe motivul ca nu e ceea ce voiai tu atunci s-a terminat. Ai ramas cu ea pe cap...astia nu au de gand sa faca retururi.

It does what it's supposed to do. Balance is the big thing. Be careful to position frames the same direction and on all sides. It helped to screw down the feet to a sheet of plywood and stand on the plywood. Definitely a great value and it's holding up.

Good quality for the price. It is a budget extractor, and the frame rests are a tiny bit large but still will hold frames ok while spinning. Perfect for any hobbie bee keeper.

This is my 1st time ever using a honey extractor. I am 2 yrs into beekeeping. This is the rundown of my experience with the VEVOR Manual Honey Extractor. Out of the box, it looked shiny and all parts accounted for. Assembly was easy and already assembled parts had tight screws. The plexiglass covers, however, were not quality cut. They have some cracks and chips but as far as function they worked. I'm not sure what was going on when I put my frames in. They kept hitting the plexiglass covers, no matter how fast or slow I spun them. But all in all, it did the job efficiently. What honey I couldn't scrape out with a spatula, sat in the bottom of the tub and I put it outside for the bees to clean up. I will say that plastic foundations would work best with this extractor. Many of my wax combs was destroyed in the spinning process. The only reason I gave it 4 stars is because of the plexiglass issues.