Kundeanmeldelser for VEVOR manuell flisekutter, 1000 mm, porselensflisekutter med skjærehjul for wolframkarbid, infrarød posisjonering, sklisikre føtter, slitesterke skinner for profesjonelle installatører eller nybegynnere

Zawiodłem się, liczyłem na lepsza jakości, przecinarka się wygina, na dodatek na środku źle docina, a czasami przy gresie 7 mm raczka opiera się na prowadnicy i nie idzie noża docisnąć bo palce przeszkadzają, ustawiałem na różnych podłożach, efekt ten sam szczególnie prze mniejszych rozmiarach płytek typu 30cm 40cm

Came partially assembled one of the side support legs wasn't installed and in order to install it needs to be disassembled , bearings not one was spinning freely because the washers were installed at the front of the spacers onto the bearings and that was stopping them from spinning so again need to be switched around so basically complete disassemble to fix this issues then the laser is not 4 screw adjustable only two and is impossible to align it if the back aligned to the cutting wheel then the front at least 1/8" off if the front aligned then 1.5 " at the back is off I tried for an hour and not possible to align it , the breaker shoe doesn't have a magnet to hold it up when you score so it's a bit annoying, I am disappointed!

Envio fora de prazo e sem rastreio. A máquina de corte de cerâmica manual chegou com defeito nas borrachas dos apoios laterais, enviei fotos da situação e estou a aguardar que enviem substituição da peça com defeito.

For the price the quality is fine, but it does have some flaws that keep me from using it on a daily basis. 1. The piece that has to snap the tile after scoring can not be held up, so it’s always hanging in the way when cutting. That is quite annoying if you’re trying to cut precisely. 2. The laser attached is basically useless, since it doesn’t have enough options to calibrate it to be precise/usable. It can only be rotated, not moved from left to right. 3. Also the guide or “tile stop” is totally out of square, so basically unusable. 4. The ad claimed it has a carbide roller blade, but it doesn’t have it. So it dulls very quickly, had to buy a real carbide blade separately. A few minor tweaks could have made it way better, but they chose not to which is disappointing.

laser never worked. have not used yet to cut but i am sure will work just fine

Mais je n’est pas réussi à couper les carreaux sur la longueur ils cassent toujours à un endroit malgres la coupe faite bien droite. Dommage. Peut être mes carreaux qui ne convienne pas.

todo ok

Ich habe das Produkt gekauft um Fliesen im Format 20x120 zu schneiden. Das Gerät ist recht simpel in der Nutzung. Leider ist die Qualität nicht sonderlich gut. Der Anschlag ist etwas schräg montiert, sodass die Fliese nicht rechtwinklig angelegt werden kann. Der Laser lässt sich ebenfalls nur bedingt einstellen, sodass er entweder am Endanschlag oder am Anfang die Schnittstelle markiert. Zudem ist die Führungsschiene etwas schwach bemessen, sodass sich beim Anreißen in der Mitte der Fliese die Führung hochdrückt und der Riss nicht sauber ist. Für den angebotenen Preis im Bereich Hobby Gerät ist es okay. Der Support zu den angegebenen Problemen war leider sehr schlecht. Mir wurde 3x die Anleitung des Produktes geschickt, statt auf die Probleme einzugehen

La taglia mattonelle e perfetta per me ha solo un difetto quando tagli le mattonelle già da 2/3 cm sulla lunghezza di 120 non si riesce a tagliare si spezza sempre e in più si inarca molto al centro andrebbe studiato un rinforzo al centro

Board is flimsy and handle is too low. I can not cut any porcelain tile strip less than 2 in.