Kundeanmeldelser for VEVOR manuell flisekutter, 1000 mm, porselensflisekutter med skjærehjul for wolframkarbid, infrarød posisjonering, sklisikre føtter, slitesterke skinner for profesjonelle installatører eller nybegynnere

The tile cutter works well. Unfortunately there’s a bolt that keeps falling off

Für gelegenliches schneiden der fliesen , mit reichlicher zeit wird der fliesenschneider reichen , das schneiderad ist leider etwas zu hoch für die fliesen , es hätte ruchig tiefer sein können .

Lo compré hace un año y ya se ha roto. He hecho unos 100 m² con él, ¡pero eso no significa 100 m² de corte real! En resumen, no lo llamaría profesional en absoluto, ¡y mucho menos a su servicio de atención al cliente! Expliqué mi problema, pero me han tenido mareando la perdiz de un lado a otro con gestiones de tickets que no han servido para avanzar nada. Había enviado fotos, pero me exigieron hacer un vídeo de un rodamiento que supuestamente estaba roto para que los "ingenieros" lo revisaran. En definitiva: muchas complicaciones y ninguna solución. ¡Así que hoy tengo un cortador de azulejos de 125 € directo para la basura!

Zawiodłem się, liczyłem na lepsza jakości, przecinarka się wygina, na dodatek na środku źle docina, a czasami przy gresie 7 mm raczka opiera się na prowadnicy i nie idzie noża docisnąć bo palce przeszkadzają, ustawiałem na różnych podłożach, efekt ten sam szczególnie prze mniejszych rozmiarach płytek typu 30cm 40cm

Came partially assembled one of the side support legs wasn't installed and in order to install it needs to be disassembled , bearings not one was spinning freely because the washers were installed at the front of the spacers onto the bearings and that was stopping them from spinning so again need to be switched around so basically complete disassemble to fix this issues then the laser is not 4 screw adjustable only two and is impossible to align it if the back aligned to the cutting wheel then the front at least 1/8" off if the front aligned then 1.5 " at the back is off I tried for an hour and not possible to align it , the breaker shoe doesn't have a magnet to hold it up when you score so it's a bit annoying, I am disappointed!

Envio fora de prazo e sem rastreio. A máquina de corte de cerâmica manual chegou com defeito nas borrachas dos apoios laterais, enviei fotos da situação e estou a aguardar que enviem substituição da peça com defeito.

For the price the quality is fine, but it does have some flaws that keep me from using it on a daily basis. 1. The piece that has to snap the tile after scoring can not be held up, so it’s always hanging in the way when cutting. That is quite annoying if you’re trying to cut precisely. 2. The laser attached is basically useless, since it doesn’t have enough options to calibrate it to be precise/usable. It can only be rotated, not moved from left to right. 3. Also the guide or “tile stop” is totally out of square, so basically unusable. 4. The ad claimed it has a carbide roller blade, but it doesn’t have it. So it dulls very quickly, had to buy a real carbide blade separately. A few minor tweaks could have made it way better, but they chose not to which is disappointing.

laser never worked. have not used yet to cut but i am sure will work just fine

Mais je n’est pas réussi à couper les carreaux sur la longueur ils cassent toujours à un endroit malgres la coupe faite bien droite. Dommage. Peut être mes carreaux qui ne convienne pas.

todo ok