Kundeanmeldelser for VEVOR Magnetisk Drill 1300W 2922lbf/13000N Portable Mag Drill Press 810RPM

Produit ok n'a rien a envier aux marques pro. Puissante, un aimant qui accroche bien. Ne peux être activée en rotation si pas activée en magnétique: donc bonne sécurité.

Jako oštećena kutija prilikom preuzimanja - proizvod nije bio oštećen Dobro izgleda - probušio par rupa dobro radi. Preporučam za tu cijenu od 185 e L.p.

Subject: Review - Magnetic Drill 1550W Hello, For a long time I had been considering purchasing a magnetic drill. When I saw the price of $300 and having been satisfied with your products so far, I couldn't resist. The Good: The drill is very solidly built and the magnet holds very well. Design Limitations: Unfortunately, the drill can only run when the magnet is engaged. This is sometimes inconvenient when you want to precisely position a drill bit on a center mark - although I understand this is probably a safety feature. Technical Issues: The variable speed controller is a very useful feature. However, under certain conditions the controller begins to oscillate, which indicates a poorly tuned PID regulator. I modified the machine to use only a simple dimmer without a control circuit, but unfortunately this was also not a great improvement because the motor's internal resistance is too high, causing the speed to drop too much under load. Conclusion: Overall, I am very satisfied with the purchase and for $300 it is an excellent value. Dip.-Ing. J. Feldheim

Aufgabe erfüllt - leider gab es die Bohrmaschine kurzfristig nur ohne Linkslauf - sonst zufrieden

I have built stuff all my life, lived on several farms, do a lot of experimenting building all sorts of items. I just recently bought this drill because I am getting ready to put a roof over two shipping containers. I need to drill 80 holes in the sides of the containers - I think about 16 gauge or 1.5mm thick steel. The thought of holding an electric drill and drilling by hand, while on a ladder (⅜" or 10mm holes), got me thinking about how to do this easy. I remembered using a magnetic drill once when I was a teenager - and I started looking around.$1k for a nice Milwaukee, $850 for a Makita - this Vevor at $250 works well. I haven't drilled the containers yet, but I've used it on several other projects - drilling over dozen of ½" holes in ¼" steel, some thru 2 layers of ¼" at a time. I drilled one 2" diameter hole with a Milwaukee hole saw bit. It did a very good job on all of these. The drill works, but it has some issues that could be improved (Vevor design and manufacturing please take note). The speed control isn't very good - when drilling large diameter holes in steel (what else would you drill with a magnetic drill???) the drill needs to turn at a constant slow RPM. When at low settings (I think the drill is just marked in 0-1-2-3... actual RPM numbers would be very helpful here) the speed will vary considerably with load. This is an annoyance, and requires some adjusting the speed as you start drilling, but stabilizes once the hole is started. The other issue is - and it may be the model I chose - seems to be quite a few similar mag drills by Vevor - I chose the most powerful at 1550W. The drill came set up to drill with end mill holders - for machine shop type end mills. There is an regular adjustable (key) drill chuck that will take up to ¾" bits (I think), but when I put the adjustable chuck on, then my standard sized ½" bit was too long. To use the drill with the adjustable chuck, I had to disassemble the up/down track mechanism and reassemble upside down. But my drill wasn't really setup to do this, but I was able to make it work. The tracks have adjustable tension tracks maybe 6 or more locking set screws on the track - and brass I think which is good because it slides well) It does not crank up and down with equal resistance, even though I adjusted it several times - too loose and the drill falls down, too tight and it's a b**ch to raise). But it is very useable, just I think Vevor needs to keep working on improvements, which I think they will. I have bought several other items from Vevor and all have been nice tools or materials (I forgot what they are, and they didn't get listed on my account). I will continue to look first to Vevor when buying tools, as the prices are excellent and the quality had been pretty good for tools that aren't in a production line constant daily use type work. I think Vevor is trying hard to be a quality supplier. I wish them well, and hope that they are all happy and heal

Drills holes magnet seems good, only thing doesn't have a safety kick off for when the magnet loses contact

multumit

Great drill, just drilled some holes in 10mm plate and it worked effortlessly but small problem I encountered was the chuck was a bit shaky when starting the hole but I’m hoping to tune it a little to eliminate this problem.

Good so far, works as expected

un buen desempeño llevó al rededor de un año... y a salido muy bueno