Kundeanmeldelser for VEVOR Single Horn Ambolt 44Lbs Steel Ambolt Smed til salgs Smiverktøy og utstyr Ambolt Robust Rundt og firkantet hull Horn Ambolt Smedsmed Juvelerer Metalsmith Smedverktøy

Contexte : Amateur pas trop musclé Remarques : Je pensais que ce serait plus imposant, mais c'est suffisamment lourd comme ça. Contre: Emballage qui a un peu souffert, mais l'enclume est intacte (pas sûr que ce soit le cas pour les objets autour) Pour: Pas de surprise, identique à la photo. Bleu moche, mais bel état de surface sur la zone de travail. J'ai enfin réussi à plier une patte métallique assez épaisse sans rien casser, ni risquer de me faire mal. Pas de trace de frappe sur la surface après le premier essai. Ca devrait parfaitement convenir à mes petits bricolages d'amateur.

I’m pleased with this anvil, solid, good face. It was delivered very quickly. The only issue I have was that there was a bunch of Bondo on the underside and the horn had cast marks on it. I highly recommend this anvil.

I've been using this anvil for alittle over a month and it seems to be a great anvil for a low cost. It has great rebound and has been able to do what I need it to do. It has a few small flaws but for the price you can deal with it.

I have been making blades for over four years, and wanted a second anvil. I saw the attractive price and decided to try it out. The description says it's cast steel (never purchase a cast iron anvil. Iron is to soft) and it had a 52 hardness. I built a three legged base with 1/4" 2"x2" tubing for the legs and 1/2" plate steel for the base for the anvil to sit on. I filled the legs with sand, tapped the legs with a hammer to get as much sand to compact. This adds weight that you want to keep it from jumping around when using. I dropped a 1" steel ball bearing on the anvil after attaching it to the base from 2' above. The "rebound" of the bearing was 14". When striking some HOT out of the forge 1095 carbon steel with a 3# cross pein hammer, the sound of the strikes were dull and low. (that's what you want) The farther toward the rear of the anvil you strike, it doesn't have the same sound or recoil as the center of the anvil. I also question the hardness of the face. I did manage to put a small dent in the face. I will test the hardness later to see what I get. Overall, it's a great buy at the price! It doesn't come close to my 300#TFS anvil, but it also didn't cost $2,800.00. I would recommend this VEVOR anvil to anyone getting into blacksmithing/bladesmithing, or just needing something to pound on.

Excellent value. Not a “perfect “ anvil, but fully functional and all working surfaces flawless. Pritchel hole is too large and in a bad position. I machined an adapter that works pretty well. Rebound is better than my old anvil but not as good as some. However rebound is related to hardness and too hard would make it prone to chipping. I’m happy with it.

I bought this anvil for two reasons. 1) It has an HRc hardness of ~55, instead of only ~50 which is what the blue ones are. 2) Because the picture shows the horn and round hole being flush with the flat surface of the top of the anvil. This second reason turned out not to be the case. There is about a 1/ to 3/8 inch step there. I have since learned that the step is useful for some things but it does mean the round hole is not the same height all the way round, which makes it less useful for using it as a Pritchard hole. I plan to weld some fender washers onto the end of a pipe that will fit in that hole, and then grind one side flat to fit in the hole and solve this problem. The anvil itself is quite good, and for the price is down right amazing. Edges are sharp, so you can break the corners with a file to set the corner radiuses at the size you want. The anvil rings a bit, but I think with a magnet under the horn and a chain around the base this tones it down nicely. (other anvils also ring and can be quieted the same way)

Should give me alot of years of service,thanks vevor for giving good products at great prices with exceptional customer service.

The horn could be more smooth. I will have to grind it. One of the holes should have been square, but both holes are round. Apart from these things, I am satisfied.

Je suis contente de l'enclume, mais je l'ai reçue avec l'emballage déchiré. Il aurait fallu un emballage plus solide, car il était un peu léger par rapport au poids de l'enclume.

correspond à l'article sur votre site -forme -qualité -présentation -petit bémol l'emballage à revoir -Livraison dans les temps