Kundeanmeldelser for VEVOR NEMA stålskap, 20x20x15 cm NEMA 4X stål koblingsboks, IP66 vanntett og støvtett, utendørs/innendørs elektrisk koblingsboks

I'm the IT Mgr for an agricultural cooperative and much of our hardware is in very dusty, dirty environments. This is being used to house a SFF PC and PoE switch in a grain dump pit. We mounted it on the block wall, placed the hardware inside and all is well. This box is built very well and I like the fact that it is fully grounded, including the door.

Very decent, sturdy quality. Price is comparable with a similar made German produced enclosure, but easier and faster to order here. Also the available dimension range/assortment for the smaller sizes enclosures is a big plus. Well done Vevor!

Perfect enclosure for my new CNC project! Easy to mount and install the components. The seal door has a good gasket.

Awesome product. Accurate description and high quality construction. Exactly what I needed for my ham radio tower project.

Used this to mount a LiFePO4 battery in my carport. For those wondering, 1.5" of XPS insulation on all sides + the SOK 51.2V battery JUUUUUST fit! Box was sturdy, straightforward and well made. Documentation included is passable. As mentioned in other reviews, the locks provided are of limited security value; these locks (https://www.amazon.ca/dp/B002FYCZS4) with their trim collar work acceptably, but a girthier lock is probably ideal.

This NEMA 4X Enclosure met and exceeded all expectations, our Service Tech that did the install commented that it was an Awesome product. I will definitely use Vevor in the future.

I plan on purchasing many more in the near future they work great for my invention. I would like a discount on future purchases, I have purchased 13 of these this month. Can I buy them wholesale in quantities of 10.

Good quality easy to install. Good quality for the price. I have a 15A powerpoint wil a meter to monitor the amount of electricity I use to charge my car.

La réalisation du boîtier semble être de très bonne qualité. Le joint est ferme, ce qui laisse présager une parfaite herméticité de l'ouverture du boîtier. Il y a cependant quelques points de vigilance à retenir : - Les trous ne sont obstrués que par des capuchons en plastique blanc. Si les 4 au dos du boîtier seront obligatoirement ôtés pour le fixer à un support, et les trous comblés par la vis qui va traverser chacun d'entre eux, ainsi que l'écrou intégrant un joint caoutchouc placé à l'intérieur du boîtier, les 2 sur la face avant permettant d'inverser la position des charnières restent obstrués par ces mêmes capuchons en plastique de façon permanente, uniquement emboîtés dans le trou. Il n'assurent aucune étanchéité et l'écart entre la porte et leur emplacement est suffisamment grand pour laisser passer l'eau, même par simple ruissellement. Il faudrait utiliser ce boîtier annoncé IP65 dans un endroit protégé pour assurer l'absence d'infiltration d'eau, ce qui est plutôt illogique. - L'ouverture du bas sur laquelle se fixe la plaque à usiner, pour placer des presse-étoupes par exemple, est légèrement surélevée par rapport au bas du boîtier. J'imagine que cela permet d'éviter l'infiltration d'eau par capillarité, mais cela créé également un petit volume à l'intérieur du boîtier en bas dans lequel l'eau qui s'est infiltrée peut stagner et aboutir à un fort taux d'humidité fatal pour les équipements qu'il renferme. Un petit trou d'évacuation de cette eau est à envisager, même pour évacuer uniquement la condensation causée par la différence de température entre l'extérieur et l'intérieur du boîtier. - La plaque fournie pour fixer les éléments qui seront intégrés dans le boîtier ne permet pas de bénéficier de toute la surface disponible à l'intérieur. J'ai redécoupé une plaque alu un peu plus large qui s'insère également sans problème dans le boîtier. En résumé, je ne suis pas très confiant quand au sort de l'électronique (nœuds LoRa et Meshtastic) que je vais intégrer dans ce boîtier, qui sera fixé en pied de mat d'antenne TV, en bordure de toiture, face aux vents dominants. J'espérais obtenir quelque chose de plus durable et tout aussi efficace qu'un boîtier Plexo...

Overall I’m happy with it. I’m glad I went with the 20” height. I was going to to the 16” initially as my EA Charger is spec’d a bit below that. However I honestly doubt I would have been able to make anything less than this height work. I just needed that room to work and secure the nuts. I did have to modify it a bit. I took a circular hole drill-bit to cut a half circle into the bottom rectangular opening. I did this to get the plug and cord through. I decided this much easier than opening up my charger and disconnecting everything to pull the plugs out that way. Then I would have had to reconnect it all while in the box…. No thx. Anyways all said and done, I’m very happy with it. I love the look and everything. The only down vote I give that prevented it from getting a 5 star review is the lock that comes with this box…. The “key” is a joke. No key is really even needed. You can turn this lock with almost anything small and flat. I used a car key to see if it would open it. A flathead screwdriver would work…. So I don’t think this qualifies by any stretch of the imagination to be called a Lock. So now I’m looking on Amazon for a Cam Lock. However I’m hoping Vevor Customer Service can team me the exact size. I asked under “Questions & Answers” but they responded basically saying to replace the guts of the lock with a key’d part…. That sends like much more with then ordering a whole new Cam Lock…. Anyways. That is my only real complaint. Other than that I love it. It feels really sturdy and seems to be really well made and of high qualify. I didn’t love the price… but you know, You Gotta Pay To Play. I’ll attach some pics. It’s not done. The plug situation is a mess. The Electrify American plug to the wall is beyond short. So I’m going to have to move some things around to make it all hang pretty. Will post updated pics soon.