Kundeanmeldelser for VEVOR Tykkelseshøvel, 330 mm bredt arbeidsbord, trebearbeidingsmotor med benkhøvel, spiralformet kutterhode med 24 skjær, 2000 W 23500 o/min kraftig motor, én hastighet, for harde og myke trematerialer

sprzet ok mało < nozy> ale za ta cene mega szybko obrabia twarde drewno, plus przekładania spieków jak na dzien dzisiejszy jestem mega zadowolony

2 hónapja vettem, de jobb lett volna a 3 késes. Túl vannak edzve a pengék szerintem és 2 el is tört. A garancia viszont jól működik. A magyar vámmal kicsit nehéz volt megértetni hogy garanciális alkatrészt küldtek. Nem pontos a pengék mérete vagy a központosító csavar, így csíkos lesz a felület. csiszolással megoldható. Összeségében használható de jobbra számítottam.

I was really excited to receive this planer, and I wanted to like it. I bought it for hobby woodworking after saving up for it, so my expectations may have been a little high. The planer is usable, but it has a few shortcomings. The height scale isn't very intuitive, the feed rollers occasionally struggle to pull the board through, the dust collection could be much better, and the height adjustment handle feels a bit flimsy. My biggest disappointment is the finish. The planer leaves visible lines on the wood that require extra sanding afterward. It's not a deal-breaker, and with some practice you can still achieve decent results, but I expected a smoother finish. I'm giving it 2 stars because, while the machine didn't meet my expectations, VEVOR's customer support has been friendly and helpful whenever I contacted them. I hope this feedback helps improve future versions of the product.

I first rated this 3 stars: a decent machine for the price. I dropped it to 1 star because of how VEVOR handled the defect. The problem: it leaves grooves in the wood you can see and feel, as if the inserts aren't set at equal height. Not the fine scalloping you expect from a helical head, which sands out in one pass, real grooves. I reported it with photos. As seen from other reviews, i'm not the only one with this problem VEVOR's reply: their technical department stated that the spiral head uses 24 separate blades, that "minor machining tolerances" between them cause grooves, and that if I want a smoother surface I should use a straight-blade planer instead. See attachement Read that again. You pay extra for the helical cutterhead precisely because it promises a cleaner finish and less sanding. When it doesn't deliver, their answer is to buy a different type of machine. No repair, no replacement cutterhead, no check whether my unit is out of spec... Other downsides: very loud (a genuine nuisance for neighbours); the dust hood is awkward to fit, as it lifts while you tighten the bolts; and with extraction connected the outfeed flap can no longer be folded up. Moving the 100 mm outlet over slightly would have solved that. In a small shop you permanently lose space. Bottom line: don't buy this for the helical head. The manufacturer won't stand behind the finish it produces, and they put that in writing.

Machine arrive endommage. Non utilisable. Mal monter, avec plusieurs panneau lateral plier. En attente du service client.

Sehr schlechte Qualität vom Hobel Ergebnis. Macht sehr tiefe riefen im Holz, dafür braucht man keinen Hobel. Der Service von Vevor ist schlecht, reagiert nicht auf Mails. Habe jetzt den Zahlungsdienstleister eingeschaltet. Nie wieder VEVOR

La table descend très difficilement et plus on descend plus c'est dur mauvaise ajustements des coulisseaux et j'ai choisi un arbre à pastille et je le regrette car la finition du remontage et le montable on voit chaque marque de pastille il faut tout poncer après Seul avantage dépasser si on prend un clou on n'a pas toute la lame à changer mais la finition est vraiment lamentable et aucun réglage possible

A megrendelt gyalut most használtam először 1 m deszkákat gyalultam vele az első 8 db deszka nagyon szépen le gyalulta utána 2db kés kieset a csavar feje le eset amivel rögzítve volt a kés.

Contacted the customer service first in two ways, and I gave them one week to reply; nothing so far, so I must come out with the negative review. Firstly, I also ordered the three-blade version with two speeds 5 days ago, but it hasn't yet arrived. - This Spiral-Style Cutterhead is an absolute abomination. The finish that comes from this doesn't change if you try to swap the blades or reinstall them. Also, they can be turned around only once, with two cutting edges, not four, and they don't sell new blades, and they are made of the same steel, so it will increase the cost of a full change in comparison to a 2-3 blade one. This finish is worse than any normal 2-3 blade machine could give; it also chips against the grain the same way as "normal" blades. Leveling the table 100% isn't possible, so for anti-snipe, you must build your own base from MDF/plywood that is 100% flat, which will eat 20-35mm of height capacity. Same for most tabletop planers, some have a better quality base to calibrate flat. Waiting to get my return information and money back. So far, no reply. Previously, customer service was prompt when I had an issue, and it was solved immediately. Oak board on the picture, did the same with pine, and sanding double the normal with Festool won't fix this even.

When the Wood plate is rough the machine pulls the plate but when the plate is smooth it can't pull (it starts to slip)