Kundeanmeldelser for VEVOR ultralydrenser, 6L ultralydrensemaskin for plater, 180W justerbar tid, platerenser i rustfritt stål, 40 kHz rengjøringsenhet

The unit comes with everything you need, except setup instructions. It's fairly easy to figure out yourself but there are also YouTube video reviews that show the setup process, so easy enough. Once it is setup, it's very simple to use. The quality of the package is just "ok". The ultrasonic unit itself is quite flimsy but as long as you're not holding it you don't ever really notice that. As well the clamp that holds the motor in place kind of needs to be two handed when you're moving it up and down, and when it's full of records it's a bit of a pain. The motor assembly is surprisingly robust which makes up for the flimsiness of the ultrasonic unit. People in some of the reviews complain about the noise, but if you've ever used something like a Humminguru this thing is whisper quiet in comparison. Just make sure you use enough water, which is just over 4L. So one of those normal sized distilled water jugs plus a little more. I cleaned 8 records on my first go with the water temp set at 35C and a 20 minute run and the results were exactly like my Humminguru, if not a little better. Very happy that I can do multiple records at a time now. It comes with a drying rack which is honestly very flimsy and low quality. Pro tip: I bought a small portable fan on Amazon. I lift the records out of the water once they're done, turn the motor back on and point the fan at the side of the records and it takes about 10 minutes to dry them all. For the price, this thing cannot be beat.

This is a good machine with one serious -but correctable - design flaw. The records mount on a shaft that rotates them through the cleaning solution. The shaft connects to the motor with a set screw on a flattened end of the motor shaft. Of course, the vibrations in operation cause the set screw to loosen. The fix is to note where the set screw contacts the shaft, and use a metal cutting disk on a rotary (Dremel?) tool to take some material from the shaft a bit in from the end, and allow the set screw to work better. I augmented the unit with a PWM motor speed controller to slow the record rotation down to less than 2 RPM. I also fashioned a continuous filtering system, with a small pump that pushes the cleaning fluid through a 5 micron replaceable filter. I've cleaned about 400 records, and consumed 6 of the filters in the process. I found the 5 micron filter with 7 filters, the pump (12v, 130 PSI, 1.6 GPM, and the Pulse Width Modulation motor speed controller all on Temu.

Easy to put together and clean. Instructions explain how to use pretty well. Record cleaning assembly is easy to put together by looking at the photos on provided sheet. Works very nicely. All in all it is smaller than I expected it. Holds about 15 cups of fluid. I find it a little more expensive than it needs to be seeing how thin the outer casing is. Missing one screw knob for holding vinyl rotator onto machine. Record drying rack is terrible and I am using one from another cleaner. All in all very happy with machine.

Works well to clean vinyl records. Can be used for other small cleaning too.

This product is an ultrasonic cleaner that comes with an add-on device that clamps to the side of the cleaner. The cleaner has a heater for the cleaning solution. It's default setting is high enough to warp vinyl records, so it should be reduced to 25 deg. C (room temperature). The add-on spindle assembly is heavily constructed; but the clamp dimensions for securing it to the side of the cleaner are tight and the sides of the cleaner are of thin (probably less than 0.040" thick). I found it necessary to install flat washers (shims) between the clamp halves to increase the clearance to not be overly tight on the cleaner. The rotating spindle that holds the discs attaches to the shaft of the gear motor via a coupling having a single screw to tighten it to the flat of the motor shaft. Clearance between the ID of the coupler and the motor shaft allow the spindle to wiggle just a bit--but okay. I haven't used the record drying rack--instead preferring to dry records with a lint free cloth to avoid possible residue from the cleaning solution. The cleaner did a good job on a lawn mower carburetor--but that's not the review here. The price was good and I'm generally satisfied.

Easy to assemble and seems to working well. Had a few of the discs that are used to separate the record that the center hole was too small to go over the spindle. Had to drill them out. I wish that there were inserts included for use when cleaning 45s.

Solo comentar que me llegó sin la tuerca que sujeta al motor, y el fondo de la lavadora está llena de pegamento, no sé si afecte el funcionamiento

Unit received in good shape. HOWEVER: - No assembly instructions included (but I figured it out) - Record axle would not fit on motor spindle ( had to drill it larger to fit) - 3 of 8 record separators would not fit on record axle (had to drill them larger to fit) Unit take a LOOOOONG time to come to temperature. Haven't tried it out yet because I'm still waiting.

This cleaner worked as described, delivery was a bit slow but all good. I have started using it on my vinyl collection definitely noticed the difference when playing them.

So far so good. Cleaned a lot of records and and some jewelry with the little basket. Need to purchase a bigger basket for larger items to clean. I'm happy with it.