Kundeanmeldelser for VEVOR arbeidsbenk justerbar høyde, 122 cm B x 61 cm DX 97 cm H garasjebord med 72–97 cm høyde og 900 kg lastekapasitet, med strømuttak og bordplate i hardtre og metallramme og fotputer, for kontor og hjem

There is zero overhang on this work table so if you require clamping it’s next to impossible. It’s a good for a desk, not for a workshop table.

Tavolo di buon spessore , prese collocate in posizione buona, se si alza troppo il tavolo diventa un po' instabile

Très bonne qualité. Le plateau est très bien. Le bloc prises 220V + USB est très pratique. Le seul reproche est le moyen d'assemblage des pieds repère P5. Il est impossible de serrer suffisamment avec les grandes vis F4 car la pièce P3 se déforme en se repliant sur elle-même. J'ai donc remplacé, par pied, les 2 grandes vis F4 par 4 vis plus courtes. Ainsi, la pièce P3 ne peut pas se déformer et l'assemblage est parfaitement serré et stable. Il faut que vous changiez la conception au niveau de cet assemblage en remplaçant les 8 vis F4 + 8 écrous F3 par 16 vis F2 + 16 écrous F3. Une alternative à cela serait de laisser la visserie telle qu'elle est, mais d'ajouter 8 tubes métalliques entretoises qui empêcheraient les pièces P3 de se déformer en se refermant.

Per essere bello e comodo, lo è! Facile da assemblare e non pesante. Piace che non abbia il ripiano sotto anche se poteva esserci ma facilmente amovibile. L'unico particolare da migliorare è rinforzare la stabilità delle zampe in modo da non permettere che si divarichino rispetto al piano del tavolo. Sommariamente un buon banco.

Bello e solido. Tuttavia ii bulloni che fissano l’altezza di ciascuna gamba, non possono essere serrati bene perché piegherebbe le gambe( che sono travi a C ). Ho aggiunto un distanziale per bullone, all’interno della C, in modo da poter serrare bene senza piegare nulla. É diventato molto più stabile e ora fa il suo lavoro.

The long bolts that come with this to lock the leg height - two bolts for each leg designed to go through the gap in the legs and come out the other side. They only pinch the outside of the legs and it’s not very sturdy. Tightening them to any significant degree to achieve more sturdiness bends the legs inward. A better solution would be to include four short bolts and nuts per leg so they can be tightened from inside the leg. That way the telescoping leg pieces can be tightened very tight without bending the legs. I cut off some of the bolts it came with and also added my own. Difficult to explain. See photo. This way is much sturdier!

Good for the price but not compatible with Vevor bench Vice. Sadly the Vevor bench vice clamp doesn't fit the work bench which is unfortunate

Easy to install and decent quality especially the wooden top for the price. Would have been 5 stars if there was a “lip table top for make it easier to attach a clamp

I use this table over a 52" rolling tool cabinet. It's a little wobbly with the legs fully extended but does the job. Plus, it lacks any hangars to hold the power cable up when plugged in on the opposite side of the built-in plug bar. The finish on the metal looks durable and great for a garage environment as it looks like it will hold up. The top is solid butcher-block style rubberwood but is not oak as the description indicates. I'm happy with the purchase but would have been happier if it were 30-40 bucks less.

Sturdy table, came slightly damaged, but nothing I couldn't work around. I'm sure the weight of the item is why it was damaged.