Kundeanmeldelser for VEVOR 52cc bensindrevet T-stolpedriver, 2-taktsmotor bensindrevet gjerdepælemaskin, 1400W bærbar pæledriver med 3-stolpe drivhode (49/69/100 mm), for gårdsgjerder, ranchgjerder, veiforbedringer

It did not work as intended. There was a bolt missing cannot tighten it. It was in a bad spot.

Enfonce pieux pas top, à la première utilisation 2 piquets bois de clôture de diamètre 8 enfoncer et la dame du pilon ce brise en deux. Qualité et fixation de la dame très très légère acier zéro et pas de pièces détachées ( introuvable). Je pense que dans le sable ou terrain meuble ça peut peut-être le faire ??? Fragile je ne peu pas recommander ce produit

Couldn’t drive a 3 5/16 post more than 2” into soft ground. Very disappointed

Product looks nice. But ends there. Poorly made Product. Part identified as hammer seems to be too small for the cylinder. You have to check for proper alignment of the hammer before each post. If you don't and part is sideways, it would bust the housing. Don't expect to be able to return for a full refund, I was offered a 40 dollar refund and keep a product that is no use to me as it is. I bought it to speed up a process but complications from quality in design prevents that. Holediggers will work better and allow me to do the quality of work I expect to provide for my customers.

Didn't fit on a wooden 4x4 as advertised

Frustrated 😫 with this machine's lack of power, and the vibration keeps loosening most of the cap screws. The hammer mechanism bolts all came loose without much stress on the machine. I was driving a wood post for a fence, and it has been frustrating having to stop frequently to tighten bolts and screws so they don't go flying all over the place.

I have bought a lot of equipment from Vevor, but sadly I have to say I was disappointed with post driver. I have used several over the years, but there was one significant issue that I couldn’t get over. The collar that the driver sat on just isn’t long enough. I was trying to drive 6.5’ t-posts and the head of each post bottomed out about a 1/2” in which causes the heavy machine to be very unstable making it difficult to drive the t-posts in straight or even support it. It was literally more exhausting trying to support it than just using a manual post driver. The quality was decent and maybe a round 4x4 post might be better since it has a large flat head to rest on. It comes with different size collars to support different types of posts, so I am going to try using a larger collar with a piece of steel tube the t-post can sit in to give it more stability.

I unpacked and filled with engine oil and added enough fuel to test start. Pulled on cord about 3 Rand it started right up. Turned it off and started again a few times to make sir it was working properly. Took to job site the next day, filled it up with fuel and put it on fence pole, pulled trigger and it ran for 30 seconds. The machine died and I never got it cranked again! After diagnosing the machine to no avail, I contacted VEVOR and they made it right. Ending up having to borrow one to finish job. Thus is probably a fluke, but thanks to VEVOR for doing the right thing.

Post driver was a big disappointment. It couldn't even drive one T-post. Seller refunded and had good communication.

I was pleasantly surprised at how nice the case was that came with the pounder and all the accessories. I put a mixed fuel in and it fired up with about the right amount of pulls that I expected. The issue I ran into was that the posts I was pounding seemed to take much linger than I was expecting. I would say that it took longer than when I pound with a manual post pounder. This leaves me very disappointed because I have dozens of these posts that need to be planted in the ground over the next while and I was looking forward to being able to easily put the corner posts in and become more efficient but unfortunately that has not been my experience.