Kundeanmeldelser for VEVOR metalldreiebenk, 220 x 450 mm (8,7 x 18 tommer), presisjonsbenk-metalldreiebenk, automatisk mating, 0–2500 o/min variabel hastighet, 1250 W børsteløs motor, for bearbeiding av presisjonsdeler, myke metaller, tre, plast

The 1250w stepper/servo motor leaves lots to be desired. It is under powered for threading when RPM needs to be 2-300 rpm, frequently stalling: requiring the machine to be powered down and restarted, making you tune combo slide position to restart the threading. For just a few Pennie’s more they could add spherical thrust bearings on the slides… instead they have aluminum on aluminum surfaces which have to have clearances to turn without galling. This clearance adds huuuuuge amounts of lash. Once the housings are pocketed to allow for thrust bearings it fixes this issue completely. If you’re already a home machinist, absolutely plan on taking the time to install 8mm thrust bearings. Night and day difference. All the Gibbs must be cleaned and adjusted. All were loose. (Expected I guess) Lots and lots of screws were loose. Take the time to go through the machine to lock tite and torque everything. Lots of slop everywhere The digital feed for thread is Great! But the main drive motor shortchanges this by being too weak. Delivery is fast. I wish I bought the shorter unit as it’s more suited for the power… most likely more rigid too.

Unfortunately I received this lathe with lots of rust. Their solution, just sand it and apply rust prevention oil.

premier achat tour à métaux 7x14 pouces 550w poulie moteur ( dent cassée ) de votre marque VEVOR qui semblerait ne pas vous concerner car vendue par aliexpress re mis dans ça caisse car inutilisable ( 553.69 euros ) 2ème achat tour à métaux d'établi filetage électrique 220x450mm alimentation automatique 2500 tours mn 1250w plateau longueur 800 trop court pour mettre le tour dessus et une demi journée pour régler le tour

The Good: Solid casting with decent gib adjustments. Seems solidly built and packaged. For the basic machine it is well priced for what was received and has the potential to be an exceptional little machine for its size. The Bad: The 3 jaw chuck that came with it (sanou branded) has an error in the scroll that leaves a 0.762mm (0.030") runout. Also, the tailstock does not run parallel with the way having a 1.9mm drop over 300mm. The chuck needs to be replaced and the tailstock dismantled and shimmed (or replaced) if it is to be usable. Note that these items will be vary a great deal from machine to machine, some will be fine others like this one. The Ugly: Not really usable out of the box. Between the chuck and the tailstock, there is no way to turn a half decent part. These things can be fixed/replaced, but for an amateur just getting into lathes, this would be a show stopper.

Boa tarde Adequiri um equipamento destes e está com dou defeitos O mesmo não roda a 2500rpm conforme anúncio A bucha de fixação na está centrada as peças não fica ao centro Apenas faz 1250 rpm

So I’ve had this lathe for about three weeks. Since then I have had a few issues with it. Nothing major but until I fixed the little things I couldn’t feel confident using it. 1. When using the auto feed, the forward cut was good, then if I hit the return feed it had a deeper cut then the first. I had to make a brass shim that helped the glide plate from shifting 2. The auto feed threaded bar was touching the Manuel crank feed gear. I used a square razor blade as a shim to bring the threaded bar out just enough it doesn’t touch the gear. Razors blades make great shims btw. 3. It took some fine tuning on the tension screws to find that firm but easy turning of the cutting measurement dial. Now that these things are tweaked this machine does a great work