Kundeanmeldelser for VEVOR Betonggulvsliper 7" Walk-Behind Polermaskin 2.0HK justerbar maskin

Je l utilise pour poncer les bords

Its okay for the price

Works as described. For my application used it with water. Not so much connected to the grinder (that was to much water but sprayed on the concrete for me worked better. I did need to go over the work areas several times to get the finish I wanted.

Salve vorrei sapere perche, non vengono venduti i ricambi dal vostro sito

Works great, so much better than a hand grinder. Have used it to grind about 1000² ft so far.

La prise à un peu chauffé et les patins sont fait pour sol très souple. Mais le service après vente a su répondre présent et m'a proposé une solution. Finalement je ne suis pas mécontent d'acheter chez vevor

Great machine it ok not bad price ok not to bad fair had one issue with blade but issue was fix and good

Deocamdata, am testat doar functionalitatea, abia astept sa-l pun la treaba, la o sapa anhidrida.

Im a contractor, I install flooring for a living. Ive been installing floors and trim for 10 years. Im 28. It came to me with some runout. Fatness wise/in and out movement. And it was hopping around and kinda hard to control accurately. I think it was from being dropped during shipping, the shipping strap was broken and it had a big paint chip and dent in the handle metal. Cracked paint, but not cracked weld. Or it could just be that way since its so cheap. I didnt expect total perfection at 900 bucks. Either way I ended up shimming the mounting plate with aluminum cans. I had to do two bolts out of four to make it run true. Tried just shimming one bolt up, but couldn't get enough adjustment. But shimming two of the four bolts made it true within a 64th of an inch or probably less. You can barely feel any in and out movement now. Visually it looks to be perfect, but I can still feel a tiny wobble. But its running extremely smoothly now. Also the cheap attachments aren't flat, so they need to break in for 50 to 100 feet before they fully even out between them all. Then it gets extremely smooth to run. The blue grinding bits that they include are just the right Bond to cut into relatively hard concrete. No glazing issues. I have freeze thaw cycles here and it has no problems with hard concrete. Overall im very happy and impressed at the price point. They just need to ship with the mounting wheel detached so it cant bottom out on the motor shaft anymore during shipping. Them it'll bottom out on the dust shroud instead. Which is way preferable. I think a lot of people would get it and assume its just running that way because its cheap, when it might just need an adjustment. Saves a lot of headache. You can pretty accurately shim it with some pieces of aluminum can with a hole cut in the center to slide the bolts through. I think it took four shims on one bolt and three on the other and now it's pretty close to flat. Make sure to get the brushless one, its lower power than the bigger one, but the big one has a less efficient brushed motor. So you're going to be blowing Breakers for no extra power. And more overheating issues. I'm trying to include some photos of a 3X3 area that I ground in about 5 minutes but for some reason I can't include those here so. I ground about 3:30 seconds of an inch off of a 3X3 area in about 5 minutes and that was with a bunch of repositioning because it was such a small awkward space. So this machine should be able to do quite a bit of grinding in a small amount of time if you actually have room to maneuver it. The stoop that I ground was super rough and wavy and it is dead flat now.

I'm excited to use my new grinder but it came damaged. The strap that's used to hold the grinder to the pallet broke in transit causing the grinder to bang around in the pallet box. I tried uploading pictures but am not able to. I will contact customer support.